Huashan Replacement Brass Ceramic Disc Stem Cartridge Faucet Valve Quarter Turn 1/2" X 53mm x 12mm spline length 20 teeth(PAIR Hot & Cold)

After shelling out more than $1,200 for a Whitehaus Collection Vintage III Bridge Faucet, Bar Sink Faucet and matching Pot Filler for our Kitchen Remodel in 2012, imagine my surprise to realize that the cartriges in these stunning, high-end faucets were absolute garbage.Once a year at least one cartridge would fail (leak) and need to be replaced. The only place to find these was directly from Whitehaus Collection and they sold them for $60 each! That one heck of an reocurring dividend for them on a $1,200 sale especially when you count the number of times I also had to replace o-rings and nylon washers to prevent leaks elsewhere on the body of the faucets! It was so common that something would fail that I'd buy a spare cartridge or o-ring each time I had to order a replacement from the manufacturer.Frustrated, I made it my quest to find the 3rd party supplier of these cartridges. I tried off and on for years but to no avail. Underterred, I started mapping out the threads, length, splines etc of the OEM cartridge and with every order of a $60 replacement cartridge, I'd search Amazon and other plumbing suppliers and ecommerce platforms to find a lower cost replacement.Finally, last week EUREKA... I got this PAIR of hot and cold all brass ceramic cartridges for $10 with free prime shipping and not only did they fit perfectly but they also work perfectly, no leaks, smooth operation and the water turns off when you turn the handle. Fingers crossed, they will last as long or longer than the ones from the OEM. They worked so well, that I came back and bought 4 more sets - 8 cartridges for less than the price of one from the manufacturer. Now I have in inventory to last me a few years with no fear that they might someday dissapear off of Amazon. Buy these if you have a Whitehaus Collection Vintage III bridge faucet!!! 10 out of 10!

Excellent product! Only issue was adapter for faucet handle was much longer. But used existing screw and all good

This works well in the discontinued Ikea Apelskar bath faucet (which looks similar to the RUNSKÄR). The handle is a little tight to slide on the top of the cartridge, but it does fit.In the original faucet, both cold and hot turned on when turning counter-clockwise, like the Hot cartridge does in this Huashan product. If you want to keep the same direction as the original cartridges, use the Hot cartridge in either side, and discard the Cold cartridge from the Huashan set. I didn't mind reversing direction of the Cold side so I used the Cold cartridge from the Huashan set (and would use the Hot cartridge on the Hot side).Tips for disassembling this Ikea faucet: the decorative knob cap unscrews just above the red or blue colored band. Unscrew it by hand or using pliers over a piece of rubber or shelf liner so you don't scratch it. Once the cap is removed, use a Philips screw driver to remove the screw from deep inside the handle, and pull the handle off. Then use an adjustable wrench to remove the decorative cover over the cartridge. Finally, make sure the water if off below the sink, and then use the wrench to unscrew the old cartridge (it may need a lot of force). Make sure to remove the old washer, which may be on the bottom of the old cartridge or may be inside the faucet base.

If you have a Runskar (or any other Ikea faucet that is similar) that needs a ceramic cartridge replacement, this one definitely fits very well!. One can get free spare parts from Ikea, but you are limited to one at a time. Hopefully these cartridges last as long as the originals. But at this price, it wouldn't be so bad to get them again to replace the faucet cartridges again.

They are the same quality as the ones at Home Depot. But the circumference is too wide and I can't the screw ring over it to fasten it down. Threads and length are the same, but I must have an old system which is no longer in use. (1988).

OK, first let me say that I had two Aquasource (#289839) 8" spread lavatory faucets, so before I ordered these valves, to fix the old stuck cold side on the faucet at my property, I just swapped the entire cold valve assembly and handle from the extra faucet I had, and then I bought these valves to replace the just pulled cold assembly. I mention this because I do not have a need for my 2nd faucet right now and hence cannot say whether my new valve just purchased will be leak free. However, I was compelled to leave my review now because I put the new cold valve in the old faucet cold assembly I pulled and the fit was PERFECT. All the threads were in great shape, the handle fit perfectly on the 20 count threaded valve stem top, and the valve screwed into my old assembly beautifully. I put that all back in the box of my extra faucet box, so when needed, I have basically a brand new faucet ready to go, PLUS the extra HOT valve in the 2 set purchase that I did not need currently, all for $10, properly wrapped for protection and promptly shipped! I could not be happier to repair a quality old faucet like this with these quality replacement valves so economically! Note that I gave 4 stars in the "Instruction Quality" section, only because there were NO instructions, BUT NONE ARE NEEDED. Anyone who cannot clearly and easily see how these new valves go into the faucet's valve and handle assemblies has no business ordering nor using these, because it is such a basic fix.

These are a good replacement valve

The product was good, but the second charge of $15.89 (continuity subscription) is wrong and should be credited to my Visa account. This charge was not on my bill, and I did not authorize this charge.